Number of items at this level: 154.
.
., Shaileja (2017) Identification of Potential Hazards and Critical Tasks Involving High Risks and Providing Additional Control Measures. MTech thesis.
A
Agrawal, Priyanka and Varma, Nitish (2014) Experimental and Numerical Investigation of Strength of Inertial Entrainment. BTech thesis.
Agrawal, Sonam (2011) Effective Thermal Conductivity of Epoxy Matrix Composites Filled With Titania(TiO2) Powder. BTech thesis.
Agrawal, Sriyanka (2009) Calibration of Capillary Type Thermal Mass Flowmeter. BTech thesis.
B
Bathala, Srikanth (2011) Composites for machine tool beds. MTech thesis.
Behera, Dibyajyoti and Mohapatra, Abinash (2007) Design of a pen which remembers what it writes. BTech thesis.
Behera, P (2013) Experimental studies on utilization of used transformer oil as an alternative fuel in a DI diesel engine. PhD thesis.
Behera, S (2010) Study on Mechanical Behavior of Polymer based Composites with and without Wood Dust Filler. BTech thesis.
Bhargav, K V J (2023) Development of μ-ECDM System with Different Process Modes for Machining of Micro Features and Nanoparticles Synthesis. PhD thesis.
Bhaumik, Debrup (2017) Risk Assessment of Rotating Equipment by Using HIRA Methodology. MTech thesis.
Biswal, Deepak Kumar (2019) Study on Buckling, Free Vibration and Parametric Resonance of Sandwich Shell Panels with Viscoelastic Material Core. PhD thesis.
Boddikondla, Rajesh (2017) CFD Analysis of Sloshing Effect in a Rectangular Tank With and Without Baffles Under Linear Acceleration. MTech thesis.
C
Chaini, Upasana (2017) Entrainment Using Rotary Motion. MTech thesis.
Chaturvedi, Abhishek (2017) Fabrication and Characterization of Luffa Fiber Reinforced Polymer Composite and Development of Experimental Set-up for Thermal Free Vibration. MTech thesis.
Choubey, Mayank (2019) Modeling of Vibration Assisted Micro Electrical Discharge Machining for Fabrication of Micro Holes in Inconel 718. PhD thesis.
Choudhury, Balaji Kumar (2009) Process Design of Turboexpander based nitrogen Liquefier. MTech thesis.
Chowdhury, D (2010) Study on Mechanical Behavior of Wood Dust Filled Polymer Composites. BTech thesis.
D
Dalai, Radharaman (2012) Hyperbolic axial dispersion model. MTech thesis.
Das, Ananta Kumar (2015) Phase‐Split in Two‐Phase Flow through T‐Junction. MTech thesis.
Das, Liza (2011) Effective Thermal Conductivity of Epoxy Matrix Composites Filled With Aluminium Powder. BTech thesis.
Das, Saikishan and Prasanna, K (2010) Multiple robot co-ordination using particle swarm optimisation and bacteria foraging algorithm. BTech thesis.
Dash, Subjit (2017) A Project Report on “Implementation of Contractor Safety Management at One of The
Largest Steel Plants in Odisha”. MTech thesis.
Datta, Abhijit and Manna, Swarnendu (2007) Kinematic analysis of wheeled mobile robot. BTech thesis.
Datta, Sandip and Samad, Sabir Kumar (2007) Data mining of machine design elements using AI techniques. BTech thesis.
Debnath, Kishore (2011) A study on mechanical behavior and damage assessment of short bamboo fiber based polymer composites. MTech thesis.
Debta, Malaya Kumar (2023) Surface Modification of Ti-6Al-4V Alloy by Depositing MMC Coating with Variant of Matrix Phases through TIG Cladding Method. PhD thesis.
Dikshit, Vishwesh (2007) Development of compact copper-stainless steel heat exchanger using diffusing bonding techniques. MTech thesis.
Dung Dung, Tom Atul and Sharan, Ashutosh (2012) Prediction of Fatigue Crack Propagation in Circumferentially cracked pipe using CASCA and FRANC2D. BTech thesis.
Dwivedi , Piyush and Vishal , Vivek (2007) Particle swarm optimization applied to job shop scheduling. BTech thesis.
G
Gadhiraju, Bharath Varma (2017) Fatality Risk Control Program In Hot Strip Mill. MTech thesis.
Goyal, Rahul (2010) Optimization of Assembly Sequence. BTech thesis.
Gunde, Rajesh Babu (2007) Analysis of fatigue crack growth retardation due to overloading by using AFGROW. MTech thesis.
Gupta, Deepak (2011) Design and Analysis of a Horizontal Shaft Impact Crusher. BTech thesis.
Gupta, Gajanand (2011) Economic Design of X-bar control chart using particle swarm optimization. MTech thesis.
H
Hussain, Md.Afzal (2014) Effect of low cycle fatigue damage on tensile behavior of sensitized stainless steel. MTech thesis.
I
Inala, Ramu (2015) On the Dynamic Stability of Functionally Graded Material Plates Under Parametric Excitation. PhD thesis.
J
Jacob, Arun (2015) Effect of Micro-blasting on Characteristics and Machining Performance of PVD AlTiN Coated Cutting Tools. MTech by Research thesis.
Jaipuria, Sanjita (2015) The Effect of Uncertainties on Multi-Echelon Serial Supply Chains. PhD thesis.
Jasti, Anurag (2017) Modelling and Analysis of Plain Weave Fabric Reinforced Composites using Finite Element Method. MTech thesis.
Jena, Prabir kumar (2009) Analysis of Combined Conductive and Radiative Heat Transfer in a Two Dimensional Square Enclosure using the Finite Volume Method. MTech thesis.
Jena, Rini (2016) Free Vibration and Buckling Analysis of Sandwich Plate. MTech thesis.
Jena , Ashutosh (2017) A Safety Project Report on Emergency Preparedness, Accident Investigation and HIRA. MTech thesis.
Jesthi, Sanjit and Chanakya, Abhinav (2007) Buffer allocation strategies in shop floor using simulation. BTech thesis.
Jhade, Vidhyasagar (2017) Effect of Base Bleed on Drag of a Boat-Tail Projectile. MTech thesis.
Joseph, Jomy (2017) Construction Safety, Risk Management System, Kochi Metro, L&T and Coal Handling Safety, JSW. MTech thesis.
K
K B, Ashita (2017) Design and Optimization of Heat Exchanger for Cooling of Supercritical Helium Using Boiling Liquid Helium. MTech thesis.
Kanchan, Manu and Bansal, Ankur (2007) Conceptual design to transfer handicapped or old people from one platform to another. BTech thesis.
Kant, Shashi (2010) Designing Automated Guided Vehicle Using Image Sensor. BTech thesis.
Kar, Amit Bikram and Saran , Abhisek (2007) Transient radiative transport in homogeneous/ non-homogeneous participating medium. BTech thesis.
Kar, Punit (2014) Design and analysis of cold box and its internal component layout for kW class Helium Refrigerator/Liquefier. MTech thesis.
Kar, Satya Prakash (2007) CFD analysis Of printed circuit heat exchanger. MTech thesis.
Khan, Irshad Ahamd (2009) Prediction of elastic properties of 2D orthogonal plain weave fabric composites. MTech thesis.
Khan, Irshad Ahmad (2015) Study of Computational and Experimental Methodologies for Cracks Recognition of Vibrating Systems using Modal Parameters. PhD thesis.
Kishore, Siripurapu Yada (2017) Design of Micro-Channel Heat Sink for Wall Temperature Uniformity. MTech thesis.
Kumar, Ajit (2017) Flow Field and Heat Transfer Characteristics of an Axisymmetric Air Augmented Rocket. MTech thesis.
Kumar, Jitesh (2023) Thermohydrodynamic Analysis of Gas Foil Bearings for High-Speed Turbomachinery. PhD thesis.
Kumar, Kamlesh (2020) Ti-6Al-4V alloy weld joint by variant of TIG welding method: Characterization and mechanical performance evaluation. PhD thesis.
Kumar, Manoj (2020) Numerical and Experimental Analysis of Cryogenic Turboexpander. PhD thesis.
Kumar, Pradeep (2011) Optimization of structural parameters using artificial neural network for vibration reduction in beams. BTech thesis.
Kumar, Rajeev (2007) Numerical solution of moving boundary problem related to continuous casting. MTech thesis.
Kumar, Shashi (2011) Prediction of crack propagation using γ-model for through wall cracked Pipes. MTech thesis.
Kumar, Sunny (2017) Effect of Graphite Particulate on Mechanical Properties of Glass Fiber Reinforced Composite. MTech thesis.
Kumar, Vikas (2017) Hazard Identification and Risk Assessment at Blast Furnace (Cast House). MTech thesis.
Kumar, Vishal (2017) Experimental Investigation of Biogas Production & Its Utilization in CI Engine-An Environmental Approach. MTech thesis.
Kumar , Shiv Ranjan (2007) Design of plant layout having passages and inner structural wall using particle swarm optimization. MTech thesis.
L
Lenka, Arunesh (2012) Optimization of hot-machining using taguchi method. BTech thesis.
M
Mahapatra, Deepak Kumar (2012) Job Shop Scheduling Using Artificial Immune System. BTech thesis.
Mandal, Sudipto (2010) Optimal Placement of Collocated Sensors and Actuators in FRP Composites Substrate. BTech thesis.
Matawale, Chhabi Ram (2015) Evaluation of Leanness, Agility and Leagility Extent in Industrial Supply Chain. PhD thesis.
Mathew, Mrudul (2017) Health and Safety Management Systems in Thermal Power Plants and Safety Inspection at L&T Constructions, Kochi Metro Rail Project. MTech thesis.
Mazumdar, Sourav and Singh, Rahul (2007) CFD studies on flow through compact heat exchangers. BTech thesis.
Meena, Vishvendra and Saroya, Avtar (2011) Study of Mechanical Properties of Hybrid Natural Fiber Composite. BTech thesis.
Meher, Chitta Ranjan (2012) Damping of fixed-fixed welded joints. BTech thesis.
Mishra, A K (2014) Deformation Behaviour of C-Mn440 Automobile Steel under Varying Strain Rates. MTech thesis.
Mishra, D (2014) A study on thermal and dielectric characteristics of solid glass microsphere filled epoxy composites. PhD thesis.
Mishra, D K (2014) Thermo-mechanical Processing of API-X60 grade pipe line steel. MTech thesis.
Mishra, Kaushik (2011) Scheduling of automated guided vehicles in a FMS Environment using particle swarm optimization. BTech thesis.
Mishra, Suyash (2012) Analysis for Water Hammer considering the effect of Fluid Structure Interaction in Straight Pipes. BTech thesis.
Misra, Nitish (2017) Identification and Mitigation of Risk Associated with Eot Crane During Material Handling. MTech thesis.
Mittal, Himanshu (2017) Simulation Study of Luffa Fiber Reinforced Composite Under Various Geometrical Parameters. MTech thesis.
Mohanty, Chiranjiv (2011) Experimental investigation of the combustion, performance and emission parameters of a compression ignition engine using blends of vegetable oil and diesel fuel. BTech thesis.
Mohanty, Tapas Ranjan (2020) Investigations of Blast Furnace Cooling Staves and Intelligent Prediction Using Artificial Neural Network. PhD thesis.
Mohapatra, Jeet (2015) Non Fourier Heat Transfer Across a Gun Barrel. BTech thesis.
Mutra, Rajasekhara Reddy (2019) Dynamics and Control Simulations of Turbocharger Rotor-Bearing Systems. PhD thesis.
N
Naik, Danavath Vasu (2017) Mechanical and Tribological Behavior of Rubber Wood Fiber Reinforced Epoxy Composite. MTech thesis.
Nangia, Aniket (2012) CFD analysis of a vertical tube with external helical fins in natural convection. BTech thesis.
Nayak, Bijaya Bijeta (2015) Parametric Optimization of Taper Cutting Process using Wire Electrical Discharge Machining (WEDM). PhD thesis.
Nayak, Paresh Ranjan (2007) Electronic chip cooling in vertical configuration using fluent gambit. BTech thesis.
O
Ohid, Soumya Aditya (2007) Bullwhip effect in supply chain management. MTech thesis.
P
Panda, Raunak Kumar (2017) Enhancing the Capability & Competency of Vendors for Continual Improvement in their Safety Performance at Tata Steel. MTech thesis.
Panda, Sandeep Ranjan (2016) Study and Design of Helium Scroll Compressor. MTech thesis.
Panigrahi, Priya Ranjan and Gouda, Bimal Kumar (2007) Development and study of erosion characteristics of PEEK - glass fiber composites. BTech thesis.
Parida, Smita (2018) On the Linear and Nonlinear Free Vibration of Functionally Graded Material Plates in the Thermal Environment. PhD thesis.
Parthasarathi, S. (2017) A Safety Project Report on Hazard Identification and Risk Assessment of Steel Melting Shop. MTech thesis.
Patel, Pooja (2017) A Study on Thermal Behaviour of Carbon Black Filled Epoxy Composites. MTech thesis.
Pati, Fakir Mohan (2010) Study of Parametric Optimization of Microdrilling Operation using Taguchi Method. BTech thesis.
Pati, Pradeep Kumar (2007) Design and development of an AGV using RF module. BTech thesis.
Patle, Sewan Das (2006) Analysis and Measurement of Thermophysical Properties by Temperature Oscilation. PhD thesis.
Patra, Saroj Kumar (2007) CFD analysis of electronics chip cooling. MTech thesis.
Pavankumar, Vodnala (2011) Damping of machine tool structures with riveted joints. MTech thesis.
Pedada, Sudheer Kumar (2017) CFD Analysis of Double Pipe Helical Coil Heat Exchanger With Micro-fin Inserts. MTech thesis.
Pradhan, Piyus (2017) Hazard Identification and Risk Assessment at New Plate Mill, RSP Rourkela. MTech thesis.
Pradhan, Subhrajit (2017) Moisture Absorption Behavior and its Effect on Mechanical Properties of Orange Peel Reinforced Polymer Composites. MTech thesis.
Prakash, R (2013) Experimental Studies on a DI Diesel Engine Fueled with Jatropha Methyl Ester-Wood Pyrolysis Oil Emulsions. PhD thesis.
Pujapanda, Asim and Acharya, Sibashish Priyadarshi (2007) Identification of control chart patterns using neural networks. BTech thesis.
Purohit, Abhilash (2014) Dephosphorization of steel produced from sponge iron in the induction furnace. MTech thesis.
Pyasi, A (2014) Value added metal extraction from red mud. MTech thesis.
R
Raghuvanshi , Sourabh Singh (2007) Study of digital modulation techniques in the presence and absence of noise. BTech thesis.
Rajkonwar, Amit (2017) Investigation into mechanical and tribological properties of Lantana Camara particulate reinforced epoxy composite. MTech thesis.
Rajput, Mudit (2010) CFD modelling of hot machining operation. BTech thesis.
Ramteke, Prashik Malhari (2023) Nonlinear Numerical Modelling and Analysis of Porous Functionally Graded Curved Structures under Thermomechanical Loading. PhD thesis.
Ravindra, Vutukuru (2014) Design, development and testing of nb-ti superconducting magnet & creation of liquid helium test facility. MTech by Research thesis.
Reddy, G Chanukya (2007) CFD studies on flow through screw compressor. MTech thesis.
Roul, Shakti Prasad (2011) Application of Ant Colony Optimization for finding
Navigational Path of mobile robot. BTech thesis.
S
S, Naga Mahendra Babu (2007) Processing, characterization and tribological evaluation of peek-glass fiber composites. MTech thesis.
Saeed, Ahmed (2011) Path synthesis of four-bar mechanism using harmony search optimization. BTech thesis.
Sahoo, Bibekananda (2017) Enhancement of Thermal Insulation Property of Epoxy Based Composites Using Short Natural Fibers. MTech thesis.
Sahoo, Swati (2011) Study of Capillary Filling Dynamics in a Microtube. BTech thesis.
Sahoo , Satyaranjan and Beldar, Manoj Kumar and Suman, Ajay Shankar (2012) Finite Element Modelling of Composite Rotor-Shaft-System. BTech thesis.
Sahu, Chinmaya Pratik (2017) Observation, Work at Height, Behavior Based Safety and Safety Precaution taken in Coke Oven Plant. MTech thesis.
Sahu, Deepak Kumar (2016) Sono-Electroplating of Cu-Ni Alloy Thin Films and their Corrosion Behavior. MTech thesis.
Sahu, Jyoti (2017) Risk Assessment and Safety Measures for Different Activities at Blooming & Billet Mill, Rail & Structural Mill of Bhilai Steel Plant, Chhattisgarh. MTech thesis.
Sahu, P K (2014) Study of hydrogen assisted cracking in ship building grade steel. MTech thesis.
Sahu, Pratoh Sourav (2010) Optimization of process parameters involved in laser bending operation using taguchi experimental design method. BTech thesis.
Samal, Sangram Kumar (2015) Numerical Study of Taylor Bubble Breakup by Placing Obstacle at T-Junction Bifurcation. MTech thesis.
Samanta, Abinash (2017) Numerical Analysis on Biomass Gasification in a Fluidized Bed Gasifier. MTech thesis.
Sandeep, E S (2014) Synthesis and characterization of ODS-304L steels by mechanical alloying. MTech thesis.
Sarkar, Binay Krishna (2018) Flow-Regime of a Liquid-Liquid Counter Current Two-Phase Flow. MTech thesis.
Seth, P P (2014) Study of Bak-hardening of ultra-low carbon BH 220 steel at different strain rates. MTech thesis.
Sethy, R (2014) Experimental investigation and optimisation in EDM process of AISI P20 tool steel. MTech by Research thesis.
Shantharam, Pradeep and Murali, R (2007) Creative Design of a Device that not only Cleans the Teeth but also Anti-Germinates. BTech thesis.
Shial, Satya Ranjan (2017) Development of Ti-TiC Composites by Powder Metallurgy Route Using Recycled Machined Ti Chips. MTech thesis.
Shrivastava, Amit Kumar (2011) Optimization of robotic assembly of printed circuit board by using evolutionary algorithm. MTech thesis.
Shukla, Ajay (2017) Hazard Identifications and Risk Assessment at Steel Melting Shop in JSW Steel Mumbai. MTech thesis.
Singh, A K (2010) Effect Of Vibration on Delaminated Beams. BTech thesis.
Singh, Anurag and Singh, Prashant (2012) CFD Analysis of Stirling Cryocoolers. BTech thesis.
Singh, Deepak (2017) Free Vibration and Buckling Analysis of Carbon Laminated Aluminium Reinforced Epoxy. MTech thesis.
Singh, Pravin (2017) Numerical Investigation of Lmni5 Based Solid State Hydrogen Storage Device. MTech thesis.
Singh, Susheel and Pradhan, Sidharth (2010) Thermal Analysis of Wire-Screen Regenerator Matrix Using CFD. BTech thesis.
Singh, Tej Pratap (2020) Heat Transfer and Fluid Flow Analysis of a Turbulent Jet Flowing Over a Sinusoidal Wavy Surface. PhD thesis.
Singh, Yogesh (2012) Free vibration analysis of the laminated composite beam with various boundary conditions. MTech thesis.
Soni, Pankaj Kumar and Gholley, Raju (2007) Study and analysis of residual stresses in electro-discharge machining(EDM). BTech thesis.
Soren, Rimil Sing (2009) Process Improvement Through Reverse Engineering. BTech thesis.
Srivastava, Shivam and Saraogi, Mayur (2007) Electronic chip cooling in horizontal configuration using fluent-gambit. BTech thesis.
Srivastava, Tushar (2017) CFD Analysis of Fin and Tube Heat Exchangers using ANSYS CFX. MTech thesis.
Suman, Sharda Devi (2017) Effect of Nano Magnetostrictive Particle on the Vibration Response of Polymer Composite. MTech thesis.
Swain, Manisha (2011) Study of Capillary Filling Dynamics in a Microchannel. BTech thesis.
T
Thrinadh, Jadam (2020) Experimental Studies on Machinability Assessment of Difficult-to-Cut alloys (Inconel 718 and Ti-6Al-4V) During Traditional and Non-Traditional Machining. PhD thesis.
Tirkey, Sanjeeb Kumar (2007) Three dimensional analysis of lateral extrusion of some complex forms. MTech thesis.
Tiwari, Pawan Kumar (2014) Experimental investigation of ethanol fueled partially premixed compression ignition (PPCI) diesel engine. MTech thesis.
Tripathy, Sasmeeta (2007) Thermal-electrical modelling of electrical discharge machining process. MTech thesis.
V
V, Devaraj and Chhabra, Yatin (2011) Mathematical and Optimization Analysis of a Miniature Stirling Cryo-cooler. BTech thesis.
V, Rahees Mohammed Kurikkal O. (2017) Risk Mitigation in Major Hazard Scenarios Through Process Safety Management and Barrier Analysis. MTech thesis.
Y
Yadav, Utkarsh (2011) Multi-criteria decision making approach for vendor selection. BTech thesis.
This list was generated on Tue Nov 12 21:33:45 2024 IST.
